L730 Loader Manual

• Flatness measuring accuracy of .00012 in/ft. (0.01 mm/m or 2 arc secs) in a 180°/360º sweep and .00006 in/ft. (0.005 mm/m) in a 90º sweep.
• Continuously rotating diode laser with 100 ft. (30.5 m) radius operating range.
• Set up in as little as 10 minutes.
• Uses A-1519-2.4ZB Single-Axis Wireless Target with .00002 in. (0.0005 mm) resolution and +/-.55 in. (+/-14 mm) measuring range.
• R-1357-2.4ZB PDA Readout displays data for up to 5 A-1519-2.4ZB Targets simultaneously.
• Coarse Pitch and Roll leveling base adjustments.
• Real-time data display.
• Backlit, precision level vials accurate to .00018 in/ft. (0.015 mm/m).
• Upgrade to L-730SP Split-Prism Levels and L-730CFU Coarse/Fine PRY Base Upgrade for .00006 in/ft. (0.005 mm/m or 1 arc sec) accuracy.
• Uses AC adapter or battery pack.
• Windows 7/8/10-based Plane5 software quickly records and analyzes flatness data.

1. Case Ih L730 Loader Specs
2. Case Ih L730 Loader
3. Case Ih L730 Loader Manual

Case IH L720,L730 Loader Operator`s Manual contains operating, maintenance, safety, and service information, PDF. Isn't Alo Quicke the same as O.E.M. Loader on Case IH? Had a joystick go bad on a new Case IH L750 loader and it was under warranty and the dealership put a slightly used joystick in off of somebody's tractor which was in the shop because it was parked outside in freezing temperatures and the engine gasket froze and broke and leaked oil out. Satellite L730/L735/Satellite Pro L730 Stress injury Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use.

If you do not see your application listed, please contact us to discuss your requirements. We will be more than happy to provide a solution that’s right for your unique alignment problem.

• Aircraft Interior Alignment (Storage Bins, Galleys, etc.)
• Floor Beam Alignment
• Jig/Tooling Leveling

• L-730 Toyostove Laser Vented Heater. WE'VE BEEN GREEN FOR 40 YEARS. A half million satisfied customers can't be wrong.From the Arctic to Antarctica, from Maine to California the revolutionary Toyotomi sealed combustion direct vent heating systems (TOYOSTOVE, Laser, and OIL MISER models) are the most fuel-efficient, energy saving, heating systems available (use up to 50% less fuel for heating.
• Front-end loaders carry, lift and deposit loose materials: sand, soil, stone, quarry slag, coal, ore and many other similar loads. The front-end loader needs tremendous power to lift and tilt the bucket located at the end of two long arms. A powered hydraulic system (or circuit) provides the necessary power to lift.

• Router Leveling and Flatness
• Woodworking Machine Leveling and Flatness

Fabrication Alignment

• Agricultural Machinery Leveling and Flatness
• Large Construction Machinery Leveling and Flatness
• Truck Bed Assembly Leveling and Flatness

Leveling

• Machine Bed Leveling
• Split Joints on Steam Turbines

Machine Tools – Lower Accuracy

• Floor and Spar Mill Leveling and Flatness
• Gantry Leveling and Flatness
• Horizontal and Vertical Boring Mill Leveling and Flatness
• Horizontal and Vertical Machining Center Leveling and Flatness
• Large-Lathe Bed Leveling and Flatness
• Machine Tool Assembly Leveling and Flatness
• Vertical and Horizontal Presses and Flatness

• Injection Molding Machines Platen Parallelism and Flatness

Quality Control

• Large-Part Flatness, Straightness and Leveling

Ship Building

Case Ih L730 Loader Specs

• Gun Bearing Alignment
• LNG Tanker Hull Construction
• Section Alignment and Layout

Automatically Rotating Laser Planes with 200 Ft. (60 m) Range

The L-730 Leveling Laser System is a highly accurate and affordable leveling laser alignment system that measures flatness or levelness of surfaces or machinery as well a straightness of machine axes. Unlike other “point-n-shoot” lasers, the L-730’s laser beam continuously rotates, which allows the use of multiple targets simultaneously. The laser plane has a measuring range of 100 feet (30 m) in radius, or 200 feet overall.

• L-730 Automatically Rotating Laser Plane with 200 ft. (60 m) Range

Case Ih L730 Loader

Extremely Flat Laser Plane

One of the critical components of any laser system is the straightness or flatness of the laser beam or plane, as this is a guide as to how accurate flatness/levelness measurements can be made.

The L-730 features a continuously rotating laser plane that is flat to .00012 in/ft. (0.01 mm/m) in a 180° sweep.

High-Accuracy Leveling up to 70% Fastwer

The L-730 features 2 built-in level vials, accurate to .00016 in/ft. (0.015 mm/m). By using multiple A-1519/A-1520 Wireless Targets, multiple surfaces or points on a machine can be leveled at the same time. This saves up to 70% over using conventional levels or optics.

Two Configurations for Many Different Applications

The L-730 Scan Laser System is ideally suited for a whole host of alignment applications. The L-730 comes in 2 configurations. The standard L-730 has a horizontal laser plane, for checking flatness and leveling. The L-730W has a vertical laser plane and is used primarily for aligning the straightness of a rail or saw.

Wireless Targets with High Resolution and Measuring Range

To measure the flatness of a surface, the L-730 system uses our wireless targets (A-1519-2.4ZB and A-1520-2.4ZB) that feature up to .00002 in. (0.0005 mm) resolution, large measuring ranges of up to ± .55 in. (±14 mm) and 2.4 GHz “Zigbee” radio wireless communication with our R-1357-2.4ZB PDA Readout, which can simultaneously display up to 5 targets.

These lightweight targets are all powered by rechargeable batteries and like all Hamar Laser systems, the targets provide real-time alignment data so misalignment errors can be fixed without changing the setup!

Plane5 Flatness Software

For wireless recording and analyzing alignment data, our color, 3-D flatness and squareness analysis software, Plane5, simplifies and streamlines the data analysis process. It can measure up to 7 different surfaces in one project setup file and present a color, 3-D graph of the flatness and squareness analysis for each surface.

Mounting Brackets and Plates for Tractors and Loaders

LOADER MOUNTS MAY NOT BE AVAILABLE FOR INDIVIDUAL SALE...AT MDS DISCRETION.

MDS is the premier manufacturer and supplier of new buckets and attachments for the skid steer, tractor loader, telehandler and wheel loader industry in North America. Whether you need a weld-on mounting plate for a new bucket or a bolt-on mounting plate for an attachment, MDS is the ultimate source. MDS can build a mounting bracket for nearly every loader built since 1960…nearly 100 different configurations. Angles, widths and spacing will vary. Most new loaders today accept the EURO/GLOBAL mount or the Universal Skid Steer Mount. Please click on the part number of the model loader below to help you with a visual reference. What is shown in the pictures is what bolt-on mounts would look like on an MDS attachment requiring bolt-on mounts. Weld-on mounts would be the same only welded directly onto the back of a bucket shell. Weld-on part numbers are the same as bolt-on part numbers follow by a -4. Most, but not all bolt-on mount kits are two piece.

Call us if you have questions or don’t see the mount you need. It is very likely we have or can build it. Please note that all needs for Pin-To-Pin Loaders will require a schematic drawing. Tractor mounting brackets available for these and many, many more.

Quicke, CAT Challenger, Fendt, John Deere, Legend/Koyker, Mahindra, McCormick, Kubota, KMW, Miller, Zetor and more.

Case Ih L730 Loader Manual